Tel No: +44 (0) 1429 836655

sales@fidgeon.co.uk

Family business suppling the Non-Destructive Testing Industry since 1975

Temoin C Test Piece

£1.00
Product Code: F05.0719

Be the first to review this product

Availability: In stock

£1.00

Details

DESCRIPTION:

Reference test block C is made of two rectified low carbon steel fit together with an air gap (0.015-mm). On each side of these bars, there are two magnets which are assembled top to bottom so that each bar may have a
North and a South poles to its ends.

The length of the indication spectrum, which can be read on the right side and the left side, indicates the quality of the magnetic ink, which is used.


FIELD OF USE:
 
Reference test block C is intended to be used systematically:

To check the performance of crack detection of magnetic inks and powders as part of the Quality Control at the manufacturing stage (7.1.1 of EN ISO 9934-2) and in use ( 7.1.2 of EN ISO 9934-2)
To compare the efficiency of magnetic inks and powders against reference samples.
To compare the performance of magnetic powders and inks of various types from the same source or from different sources.

METHOD OF USE:

Reference test block C is processed according to the method described in Appendix A of EN ISO 9934-2.
Note: Keep Reference test block C away from any magnetic field. Do not put it between the poles of any Magnetic Testing equipment in operation.

Preparation of the sample of the magnetic powder of ink:
Withdraw a sample of the new product. Refer to the relevant Technical Data Sheet.

Cleaning of the Reference test block C:
It must be cleaned using an appropriate method in order to ensure that is free of any contamination such as: Fluorescent material, oxides, grease and any other pollution.

Application of the MagneticTesting product:
The magnetic ink or powder is applied on the Reference test block C according to the following parameters:
Spraying time: From 3 to 5 seconds.
Angle of inclination of the Reference test block C: 45 deg + 10 deg. with horizontal.
Spraying direction: 90 deg + 10 deg with the surface of the Reference test block C.
  
Viewing condition under ultraviolet (UV-A) light:  according to EN ISO 3059.
Ultraviolet (UV-A) illumination: ≥ 1000 microW/cm sq (and even: ≥ 1500 microW/cm sq according to some specifications) at the level of the surface under inspection.
White light illumination: ≤ 20 lux at the level of the surface under inspection.

Result:
The total length of the indications on the right and the left sides are to be recorded. The length of the two indications should be equal.
According to the materials, which are used for the manufacture of the Reference, test block C and the magnetic powder or ink, which is under testing, the indications maybe are not always the same length.
The indication is given from the external edges, since this measurement is proportional to the quality of the product:
  Short   →  Bad
  Long   →  Good

Establish the minimum limit not to be reached (for instance by recording the indications given by a used product)
Place on the Reference test block C a label on which the minimum value and the product name are written.
 
Final cleaning:
The Reference test block C must be cleaned according to an appropriate method to ensure that is free of magnetic ink or magnetic ink particles.

Additional Information

Additional Accessories N/A
Product Code F05.0719

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.

  • Rohmann
  • Fujifilm
  • Johnson Allen
  • Chemetall
  • Magnaflux
  • Colenta
  • Tracerco
  • Gal Gage Co.
  • Tetenal
  • Radiographic Accessories Limited
  • Vertec
  • High Technology Sources Limited
  • Phoenix Inspection Systems Limited
  • AGFA
  • Wolf Safety Lamp Company
  • X-Rite
  • Balteua NDT
  • Karl Deutsch
This site uses cookies. By continuing to browse this site you are agreeing to our use of cookies. Find out more here.
x