Tel No: +44 (0) 1429 836655

sales@fidgeon.co.uk

Family business suppling the Non-Destructive Testing Industry since 1975

USM Go Base + DAC

£1.00
Product Code: F20.0105

Be the first to review this product

Availability: In stock

£1.00
OR

Quick Overview




This unit is only available to end users within the EU and not for resale outside of the EU


The USM Go ultrasonic portable flaw detector has been ergonomically designed to provide an instrument which is light, small and easy to use in the harshest of inspection environments. Its ergonomic features include;



Portability



Small size and weight, which allow the instrument to be easily operated in confined spaces and areas of difficult access.


Light enough to be carried throughout a whole day's shift


Battery provides up to 5,5 hours operation. Can be recharged on- or off-board.


Easy-to-Read Screen



A display screen which is the same size as those in other GE flaw detectors, even though the instrument is much smaller than other instruments in the range.


An 800x480 pixel display, which is better resolution than a standard DVD.


A screen with an optimized aspect ratio to ensure highly defined echo separation.


A screen which can be easily viewed, whether hand-held or  desk-mounted.


A screen which has been ergonomically sized to help reduce eyestrain. 


Ease of Use



Can be operated with one hand, leaving other hand free for other tasks, such as maintaining probe in optimum position or holding onto ladders.


Features incorporated pressure-sensitive, navigation joystick control derived from the range of remote visual inspection equipment offered by GE.


All controls within fingertip reach. User can dedicate four function keys according to preference.


A “Flip” function allows the instrument to be used equally well by left-handed and right-handed people.


A detachable stand allows the user to optimize the viewing angle, when the instrument is desk- or bench-mounted.The attachment point is suitable for a standard tripod thread.


Increasing Productivity


The USM Go features intuitive operation so there is virtually no time-consuming, learning curve. You are productive from the moment you pick it up! Navigation is simplified using the proven graphical user interface (GUI) and the innovative joystick, allowing one-handed operation and fast and accurate adjustment.


Other features allowing increased productivity are:


A robust moulded rubber casing to withstand the harshest environments and significantly reduce downtime.


The instrument is dust- and water-proof to IP67 and is tested to withstand shock and vibration.


A standard USB connection to allow data to be downloaded from the flaw detector for further analysis or storage.The instrument is standard delivered with a 2 GB SD memory card (multiple cards can be used).


Reports are produced in jpeg or bmp format so there is no need for special reading software.


A simple on-board data logger to collect and save thickness measurements.


State-of-the-art electronics, including digital amplifier,square wave pulser (optional) and digital filters for a widerange of application benefits.






















LCD Display

Active Area




 W: 108 mm (4.25”) x H: 64.8 mm (2.55”)
Size 5.0"
Pixel Resolution

800 (W) x 480 (H) dot




























Connectors
Probe Connectors

 Two LEMO-00


UT Output Connector

 SAP output, Alarm


USB Interface micro

USB connector


SD-Card Connector

Full size SD card slot to accommodate standard SD cards





































Pulser




All pulser measurements taken according to EN12668 specifications


Pulser Mode

Simulated spike standard, Uni-polar square wave optional



Pulser Voltage           (SQ Mode)



120 V to 300 V with 10 V step in a tolerance of 10%


Pulser Width             (SQ Mode)

30 ns to 500 ns with 10 ns step in a tolerance of 10%


Pulser Amplitude  (Spike Mode)

Low: 120 V, High: 300 V


Damping

 50 or 1000 Ohms


PRF

Automatically optimized between 15 Hz to 2000 Hz,3 automatic adjustment modes: AutoLow, Auto Med,AutoHigh - Optional manual control of PRF from 15 to 200Hz




























Receiver
Range

14016 mm at steel longitudinal wave (557”)


Digital Gain

Dynamic range of 110 dB, with 0.2 dB step


Analog Bandwidth

0,9 - 17,4 MHz


Filters

Broad Band

Low Pass

5MHz (also 4)

10MHz

13MHz
























Gate
Independent Gates

2 gates (A and B), Gate B supports triggering by gate A


Rectification

Positive (POS)    Full wave (FW)


Negative (NEG)       RF


Measurement Peak

JFlank




















Memory
Capacity

2 GB SD Card. Up to 16 GB memory cards can be used


Report

Report Jpeg and BMP reports

































Environmental


Battery

5.5 hours

On board charging

Off board charging with optional adaptor

Proportional battery gauge indicating remaining

operation time


Charger “Universal” AC (100-240 V, 50-60 Hz)

Meets CCC, CE, UL, CSA and PSE requirements
Size 175 mm x 111 mm x 50 mm
Weight 845 g (1.87 lb) with the battery
Languages Russian, Portuguese, Italian, Polish, Czech, English,German, French, Spanish, Chinese and Japanese


















































Protection as per Mil-Std-810F
Damp Heat &

Humidity (Storage)
10 Cycles: 10 hrs at 60°C (140°F) down to 30°C (86°F),

10 hrs at 30°C (86°F) up to 60°C (140°F), transition

within 2 hrs, 507.4
Temperature Shock

(Storage)
3 Cycles: 4 hrs at –20°C (-4°F) up to 60°C (140°F),

4 hrs at 60°C (140°F), transitions within 5 minutes,

503.4 Procedure II
Vibration 514.5-5 Procedure I, Annex C, Figure 6,

General exposure: 1 hr each axis
Shock 6 cycles each axis, 15 g, 11 ms half sine,

516.5 Procedure I
Loose Cargo (In

Shipping Container)
514.5 Procedure II
Transit Drop (Packaged

for Shipment)
516.5 Procedure IV, 26 drops
Operating

Temperature Range
0°C to 55°C (32 to 131°F)
Storage

Temperature Range
-20°C to 60°C (-4 to 140 °F) with battery, 24 hrs
Dust Proof/Dripping

Water Proof


As per IEC 529 specification for IP67 classification
Compliance

EMC/EMI EN55011    EN61000-6-2:2001      Ultrasound EN 12668        ASTM E1324

E317

ANSI/NCSL Z 540-1-1994

MIl STD 45662A

MIL STD 2154




































Options
USM Go AWS Option AWS sizing tool according to AWS D1.1 Structural

welding code

USM Go DGS Option DGS sizing tool compliant with EN 1712
USM Go Embedded

Datalogger Option
Datalogger Option

Custom linear and grid file creation
USM Go Squarewave

Pulser Option
Allows pulser parameters fine tuning

Voltage adjustment from 120 V to 300V per 10 V

steps

Pulse width adjustment from 30 ns to 500 ns per

10ns steps
USM Go Manual PRF

and Phantom Option
Allows Manual PRF optimization between 15 Hz and

2000 Hz per step of 5 Hz. Phantom PRF will help to

identify ghost echo due to multiple reflections in low materials


Details

This unit is only available to end users within the EU and not for resale outside of the EU

The USM Go ultrasonic portable flaw detector has been ergonomically designed to provide an instrument which is light, small and easy to use in the harshest of inspection environments. Its ergonomic features include;

Portability

Small size and weight, which allow the instrument to be easily operated in confined spaces and areas of difficult access.

Light enough to be carried throughout a whole day's shift

Battery provides up to 5,5 hours operation. Can be recharged on- or off-board.

Easy-to-Read Screen

A display screen which is the same size as those in other GE flaw detectors, even though the instrument is much smaller than other instruments in the range.

An 800x480 pixel display, which is better resolution than a standard DVD.

A screen with an optimized aspect ratio to ensure highly defined echo separation.

A screen which can be easily viewed, whether hand-held or  desk-mounted.

A screen which has been ergonomically sized to help reduce eyestrain. 

Ease of Use

Can be operated with one hand, leaving other hand free for other tasks, such as maintaining probe in optimum position or holding onto ladders.

Features incorporated pressure-sensitive, navigation joystick control derived from the range of remote visual inspection equipment offered by GE.

All controls within fingertip reach. User can dedicate four function keys according to preference.

A “Flip” function allows the instrument to be used equally well by left-handed and right-handed people.

A detachable stand allows the user to optimize the viewing angle, when the instrument is desk- or bench-mounted.The attachment point is suitable for a standard tripod thread.

Increasing Productivity

The USM Go features intuitive operation so there is virtually no time-consuming, learning curve. You are productive from the moment you pick it up! Navigation is simplified using the proven graphical user interface (GUI) and the innovative joystick, allowing one-handed operation and fast and accurate adjustment.

Other features allowing increased productivity are:

A robust moulded rubber casing to withstand the harshest environments and significantly reduce downtime.

The instrument is dust- and water-proof to IP67 and is tested to withstand shock and vibration.

A standard USB connection to allow data to be downloaded from the flaw detector for further analysis or storage.The instrument is standard delivered with a 2 GB SD memory card (multiple cards can be used).

Reports are produced in jpeg or bmp format so there is no need for special reading software.

A simple on-board data logger to collect and save thickness measurements.

State-of-the-art electronics, including digital amplifier,square wave pulser (optional) and digital filters for a widerange of application benefits.

LCD Display

Active Area

 W: 108 mm (4.25”) x H: 64.8 mm (2.55”)
Size 5.0"
Pixel Resolution

800 (W) x 480 (H) dot

Connectors
Probe Connectors

 Two LEMO-00

UT Output Connector

 SAP output, Alarm

USB Interface micro

USB connector

SD-Card Connector

Full size SD card slot to accommodate standard SD cards

Pulser

All pulser measurements taken according to EN12668 specifications

Pulser Mode

Simulated spike standard, Uni-polar square wave optional

Pulser Voltage           (SQ Mode)

120 V to 300 V with 10 V step in a tolerance of 10%

Pulser Width             (SQ Mode)

30 ns to 500 ns with 10 ns step in a tolerance of 10%

Pulser Amplitude  (Spike Mode)

Low: 120 V, High: 300 V

Damping

 50 or 1000 Ohms

PRF

Automatically optimized between 15 Hz to 2000 Hz,3 automatic adjustment modes: AutoLow, Auto Med,AutoHigh - Optional manual control of PRF from 15 to 200Hz

Receiver
Range

14016 mm at steel longitudinal wave (557”)

Digital Gain

Dynamic range of 110 dB, with 0.2 dB step

Analog Bandwidth

0,9 - 17,4 MHz

Filters

Broad Band
Low Pass
5MHz (also 4)
10MHz
13MHz

Gate
Independent Gates

2 gates (A and B), Gate B supports triggering by gate A

Rectification

Positive (POS)    Full wave (FW)

Negative (NEG)       RF

Measurement Peak

JFlank

Memory
Capacity

2 GB SD Card. Up to 16 GB memory cards can be used

Report

Report Jpeg and BMP reports

Environmental

Battery

5.5 hours
On board charging
Off board charging with optional adaptor
Proportional battery gauge indicating remaining
operation time

Charger “Universal” AC (100-240 V, 50-60 Hz)
Meets CCC, CE, UL, CSA and PSE requirements
Size 175 mm x 111 mm x 50 mm
Weight 845 g (1.87 lb) with the battery
Languages Russian, Portuguese, Italian, Polish, Czech, English,German, French, Spanish, Chinese and Japanese

Protection as per Mil-Std-810F
Damp Heat &
Humidity (Storage)
10 Cycles: 10 hrs at 60°C (140°F) down to 30°C (86°F),
10 hrs at 30°C (86°F) up to 60°C (140°F), transition
within 2 hrs, 507.4
Temperature Shock
(Storage)
3 Cycles: 4 hrs at –20°C (-4°F) up to 60°C (140°F),
4 hrs at 60°C (140°F), transitions within 5 minutes,
503.4 Procedure II
Vibration 514.5-5 Procedure I, Annex C, Figure 6,
General exposure: 1 hr each axis
Shock 6 cycles each axis, 15 g, 11 ms half sine,
516.5 Procedure I
Loose Cargo (In
Shipping Container)
514.5 Procedure II
Transit Drop (Packaged
for Shipment)
516.5 Procedure IV, 26 drops
Operating
Temperature Range
0°C to 55°C (32 to 131°F)
Storage
Temperature Range
-20°C to 60°C (-4 to 140 °F) with battery, 24 hrs
Dust Proof/Dripping
Water Proof

As per IEC 529 specification for IP67 classification
Compliance

EMC/EMI EN55011    EN61000-6-2:2001      Ultrasound EN 12668        ASTM E1324
E317
ANSI/NCSL Z 540-1-1994
MIl STD 45662A
MIL STD 2154

Options
USM Go AWS Option AWS sizing tool according to AWS D1.1 Structural
welding code
USM Go DGS Option DGS sizing tool compliant with EN 1712
USM Go Embedded
Datalogger Option
Datalogger Option
Custom linear and grid file creation
USM Go Squarewave
Pulser Option
Allows pulser parameters fine tuning
Voltage adjustment from 120 V to 300V per 10 V
steps
Pulse width adjustment from 30 ns to 500 ns per
10ns steps
USM Go Manual PRF
and Phantom Option
Allows Manual PRF optimization between 15 Hz and
2000 Hz per step of 5 Hz. Phantom PRF will help to
identify ghost echo due to multiple reflections in low materials

Additional Information

Additional Accessories N/A
Product Code F20.0105

Details

This unit is only available to end users within the EU and not for resale outside of the EU

The USM Go ultrasonic portable flaw detector has been ergonomically designed to provide an instrument which is light, small and easy to use in the harshest of inspection environments. Its ergonomic features include;

Portability

Small size and weight, which allow the instrument to be easily operated in confined spaces and areas of difficult access.

Light enough to be carried throughout a whole day's shift

Battery provides up to 5,5 hours operation. Can be recharged on- or off-board.

Easy-to-Read Screen

A display screen which is the same size as those in other GE flaw detectors, even though the instrument is much smaller than other instruments in the range.

An 800x480 pixel display, which is better resolution than a standard DVD.

A screen with an optimized aspect ratio to ensure highly defined echo separation.

A screen which can be easily viewed, whether hand-held or  desk-mounted.

A screen which has been ergonomically sized to help reduce eyestrain. 

Ease of Use

Can be operated with one hand, leaving other hand free for other tasks, such as maintaining probe in optimum position or holding onto ladders.

Features incorporated pressure-sensitive, navigation joystick control derived from the range of remote visual inspection equipment offered by GE.

All controls within fingertip reach. User can dedicate four function keys according to preference.

A “Flip” function allows the instrument to be used equally well by left-handed and right-handed people.

A detachable stand allows the user to optimize the viewing angle, when the instrument is desk- or bench-mounted.The attachment point is suitable for a standard tripod thread.

Increasing Productivity

The USM Go features intuitive operation so there is virtually no time-consuming, learning curve. You are productive from the moment you pick it up! Navigation is simplified using the proven graphical user interface (GUI) and the innovative joystick, allowing one-handed operation and fast and accurate adjustment.

Other features allowing increased productivity are:

A robust moulded rubber casing to withstand the harshest environments and significantly reduce downtime.

The instrument is dust- and water-proof to IP67 and is tested to withstand shock and vibration.

A standard USB connection to allow data to be downloaded from the flaw detector for further analysis or storage.The instrument is standard delivered with a 2 GB SD memory card (multiple cards can be used).

Reports are produced in jpeg or bmp format so there is no need for special reading software.

A simple on-board data logger to collect and save thickness measurements.

State-of-the-art electronics, including digital amplifier,square wave pulser (optional) and digital filters for a widerange of application benefits.

LCD Display

Active Area

 W: 108 mm (4.25”) x H: 64.8 mm (2.55”)
Size 5.0"
Pixel Resolution

800 (W) x 480 (H) dot

Connectors
Probe Connectors

 Two LEMO-00

UT Output Connector

 SAP output, Alarm

USB Interface micro

USB connector

SD-Card Connector

Full size SD card slot to accommodate standard SD cards

Pulser

All pulser measurements taken according to EN12668 specifications

Pulser Mode

Simulated spike standard, Uni-polar square wave optional

Pulser Voltage           (SQ Mode)

120 V to 300 V with 10 V step in a tolerance of 10%

Pulser Width             (SQ Mode)

30 ns to 500 ns with 10 ns step in a tolerance of 10%

Pulser Amplitude  (Spike Mode)

Low: 120 V, High: 300 V

Damping

 50 or 1000 Ohms

PRF

Automatically optimized between 15 Hz to 2000 Hz,3 automatic adjustment modes: AutoLow, Auto Med,AutoHigh - Optional manual control of PRF from 15 to 200Hz

Receiver
Range

14016 mm at steel longitudinal wave (557”)

Digital Gain

Dynamic range of 110 dB, with 0.2 dB step

Analog Bandwidth

0,9 - 17,4 MHz

Filters

Broad Band
Low Pass
5MHz (also 4)
10MHz
13MHz

Gate
Independent Gates

2 gates (A and B), Gate B supports triggering by gate A

Rectification

Positive (POS)    Full wave (FW)

Negative (NEG)       RF

Measurement Peak

JFlank

Memory
Capacity

2 GB SD Card. Up to 16 GB memory cards can be used

Report

Report Jpeg and BMP reports

Environmental

Battery

5.5 hours
On board charging
Off board charging with optional adaptor
Proportional battery gauge indicating remaining
operation time

Charger “Universal” AC (100-240 V, 50-60 Hz)
Meets CCC, CE, UL, CSA and PSE requirements
Size 175 mm x 111 mm x 50 mm
Weight 845 g (1.87 lb) with the battery
Languages Russian, Portuguese, Italian, Polish, Czech, English,German, French, Spanish, Chinese and Japanese

Protection as per Mil-Std-810F
Damp Heat &
Humidity (Storage)
10 Cycles: 10 hrs at 60°C (140°F) down to 30°C (86°F),
10 hrs at 30°C (86°F) up to 60°C (140°F), transition
within 2 hrs, 507.4
Temperature Shock
(Storage)
3 Cycles: 4 hrs at –20°C (-4°F) up to 60°C (140°F),
4 hrs at 60°C (140°F), transitions within 5 minutes,
503.4 Procedure II
Vibration 514.5-5 Procedure I, Annex C, Figure 6,
General exposure: 1 hr each axis
Shock 6 cycles each axis, 15 g, 11 ms half sine,
516.5 Procedure I
Loose Cargo (In
Shipping Container)
514.5 Procedure II
Transit Drop (Packaged
for Shipment)
516.5 Procedure IV, 26 drops
Operating
Temperature Range
0°C to 55°C (32 to 131°F)
Storage
Temperature Range
-20°C to 60°C (-4 to 140 °F) with battery, 24 hrs
Dust Proof/Dripping
Water Proof

As per IEC 529 specification for IP67 classification
Compliance

EMC/EMI EN55011    EN61000-6-2:2001      Ultrasound EN 12668        ASTM E1324
E317
ANSI/NCSL Z 540-1-1994
MIl STD 45662A
MIL STD 2154

Options
USM Go AWS Option AWS sizing tool according to AWS D1.1 Structural
welding code
USM Go DGS Option DGS sizing tool compliant with EN 1712
USM Go Embedded
Datalogger Option
Datalogger Option
Custom linear and grid file creation
USM Go Squarewave
Pulser Option
Allows pulser parameters fine tuning
Voltage adjustment from 120 V to 300V per 10 V
steps
Pulse width adjustment from 30 ns to 500 ns per
10ns steps
USM Go Manual PRF
and Phantom Option
Allows Manual PRF optimization between 15 Hz and
2000 Hz per step of 5 Hz. Phantom PRF will help to
identify ghost echo due to multiple reflections in low materials

Additional Information

Additional Accessories N/A
Product Code F20.0105

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.

  • Rohmann
  • Fujifilm
  • Johnson Allen
  • Chemetall
  • Magnaflux
  • Colenta
  • Tracerco
  • Gal Gage Co.
  • Tetenal
  • Radiographic Accessories Limited
  • Vertec
  • High Technology Sources Limited
  • Phoenix Inspection Systems Limited
  • AGFA
  • Wolf Safety Lamp Company
  • X-Rite
  • Balteua NDT
  • Karl Deutsch
This site uses cookies. By continuing to browse this site you are agreeing to our use of cookies. Find out more here.
x